Orange dual-load AGV carrying two plastic gaylords of preforms on its roller decks in a molding plant Shown: one of the two dual-load AGVs

AGVs That Keep Ten Preform Molding Machines Supplied Around the Clock

A plastic packaging plant moved every bin of preforms by hand. Han-Tek led a turnkey AGV and conveyor system that swaps full bins for empty ones at ten molding machines, 24 hours a day.

2
dual-load AGVs, each carrying an empty and a full bin
One trip drops off an empty gaylord and picks up the full one at the same machine.
24/7
production served without waiting on a fork truck
The molding department runs around the clock, seven days a week.
2006
in production since January
The system began running production after passing its site acceptance test.
2
more molding cells added to the AGV system
The plant came back to Han-Tek for each one, in 2006 and 2013.
The short version

A plastic packaging manufacturer molds PET bottle preforms on ten injection molding machines running 24/7. Each machine fills large bins, or gaylords, and people moved every full and empty bin with pallet jacks and fork trucks.

Han-Tek was the prime contractor for an automated transport system: two dual-load AGVs from Frog Navigation Systems, a roller conveyor at every machine, zoned accumulation conveyors in the warehouse and the controls that tell the AGVs which machine needs a swap next. The system went into production in January 2006, and the plant has come back for more since.

01 The Challenge

Ten machines, every bin moved by hand

Preforms drop from each molding machine into a gaylord on the floor. When a bin filled, someone had to bring an empty, pull the full one away and take it to the warehouse to cool. With ten machines running day and night, that never stopped.

01

No time to wait

A full bin has to be swapped before it overflows, at whichever machine fills next, around the clock.

02

Two kinds of bins

Most were blue plastic gaylords, but cardboard bins on wood pallets had to travel in one orientation only.

03

Tight machine clearances

Soft drops sat just inches above the bins, so raising bins onto conveyors meant reworking the machine discharge.

The goal: swap every full bin for an empty one automatically, at all ten machines, without stopping production.

Two plastic-lined gaylords and a pallet jack in front of a yellow injection molding machine before automation
Before: gaylords moved at each machine with a pallet jack.
02 What Han-Tek Did

One contractor for the vehicles, conveyors and controls

Han-Tek laid out the system, built the conveyors and controls, and managed Frog Navigation for the AGVs, magnet grid and dispatch software. Here is how a bin moves now.

  1. 1

    Predict

    Han-Tek's controls track production at every machine and send a transport order for the one that will fill next.

  2. 2

    Swap

    A dual-load AGV arrives with an empty gaylord, rolls it onto the machine's conveyor and takes the full one on board.

  3. 3

    Store

    The AGV delivers the full bin to the warehouse accumulation conveyors and picks up the next empty one.

  • Both bin types handled: the AGV fetches the right type for each machine, and a staging conveyor in the department swaps cardboard and plastic bins when needed.
  • Zoned warehouse lanes: four accumulation conveyors, with six to eight zones each, hold full and empty bins of each type, plus a side spur where AGVs pass and scrap bins leave the system.
  • Machines stay accessible: each machine conveyor rides on casters with a floor docking point, so it can be rolled aside for maintenance.
  • Faster restarts: a clean-scrap conveyor at every machine, added during the project, speeds start-up when several machines go down at once.
  • Tested twice: a factory acceptance test at the AGV builder in the Netherlands, then a full system acceptance test at the plant.
Yellow injection molding machine with an incline conveyor and soft drop filling a plastic-lined gaylord
One of the ten molding machines the system serves.
Still moving bins by hand between machines and the warehouse?

Tell us what you move, how often and how far. A Han-Tek engineer will show you where AGVs and conveyors can take it over.

03 The Results

Bins that move themselves, and a customer that kept coming back

TaskBeforeAfter
Moving gaylordsPallet jacks and fork trucksTwo dual-load AGVs
Deciding which machine is nextWhoever noticed a full binControls tracking every machine's production
Empty and full bin storageStaged by handZoned accumulation conveyors by bin type
Machine to warehouse tripsOne bin at a timeEmpty in and full out on the same trip
  • In production: the system passed its site acceptance test and began running production in January 2006.
  • Top marks from the plant: the plant's engineering manager rated every category Excellent and wrote, "Everything is good to excellent."
  • Room to grow: the plant hired Han-Tek to tie a new molding cell into the AGV system in 2006 and another in 2013.
  • Turnkey from one source: one Han-Tek project team handled conveyors, controls, installation and the AGV supplier.
Orange dual-load AGV with two roller decks on the floor during factory acceptance testing
A dual-load AGV during factory acceptance testing.
04 Common Questions

Questions about AGVs in molding plants

What is a dual-load AGV?

An automated guided vehicle with two load positions. Here it carries an empty bin and a full one, so a single stop at a machine completes the swap.

How do the AGVs find their way?

They navigate with magnets set in the floor and take orders over a wireless network from supervisory software, which gets transport requests from Han-Tek's controls.

Can AGVs work with existing molding machines?

Yes. Han-Tek added a conveyor at each existing machine, and the machine discharges were adapted so bins could ride on conveyors 12 inches off the floor.

Can an AGV system grow with the plant?

It did here. Han-Tek tied new molding cells into the same AGVs and controls in 2006 and 2013.

Still moving bins by hand?

Let the AGVs do it.

Tell us what you move and where. A Han-Tek engineer will lay out a system that runs around the clock.

800.836.0237

"*" indicates required fields

This field is for validation purposes and should be left unchanged.
Name*

Subscribe to Han-Tek Updates

Get new Han-Tek blog posts delivered to your inbox.

Prefer a feed reader?Follow Han-Tek by RSS →